Looking for:
: Online Shopping – Bedding, Furniture, Electronics, Jewelry, Clothing & more
Hide thumbs Also See for : Instruction manual pages , Service manual 33 pages , Datasheet 5 pages. Table Of Contents. Quick Links. See also: Instruction Manual. Table of Contents. Previous Page. Next Page. Sewing Machine Singer Instruction Manual 80 pages.
Page 2: Important Safety Instructions Do not expose the machine or machine case to sunlight directly. Also, do not keep it in a very warm or damp place. Straight Stitch Handle 2. Top Cover 3. Thread Take-Up Lever Inside 4. Face Plate 5. Thread Cutter Button 6. Speed Control Button 7. Reverse Stitch Button 9. Extension Table Accessories Presser Foot Lifter Foot Controller Power Line Cord Hand Wheel Needle Pack 2. Seam Ripper 4. Brush 5. Auxiliary Spool Pin with Felt Washer 6.
Screw Driver 7. To attach, insert to the right. Never leave unattended when plugged in. Always unplug this machine from the electric outlet immediately after using and before maintenance. The machine will rotate slowly at start of sewing.
Page Thread Cutter Button F. The machine will cut both threads automatically. Do not press this button when there is no fabric in the machine or no need to cut the threads. The thread may tangle, resulting in damage. According to the pattern or mode, information will be changed. Page Clear Button I. Pull the bobbin cover latch to the right and remove the bobbin cover.
Lift up the bobbin from the machine. Pull up the left end of spool pin and set the spool of thread on spool pin so that the thread unrolls from the front of the spool. Page Inserting The Bobbin 4.
Pull thread out about 10 cm 4 inches. Replace the bobbin cover. Set the left tab into the hole in needle plate and push the right side of bobbin cover down until it clicks into place. Raise the presser foot lifter. Keep this position until needle eye threading. Keep fingers away from all moving parts. Special care is required around the needle. Do not lower the threader lever while machine is operating. While sewing, special care is required around the needle.
Machine automatically feeds the fabric, do not pull or push the fabric. Page Reverse Stitching B. Place the fabric in position where back stitching is to be made and lower the presser foot. Press and hold the reverse button. Sew reverse stitch. Page Turning Corners D. Stop the machine when you reach a corner. The machine will stop the needle into the fabric.
Raise the presser foot. Use the needle as a pivot and turn fabric. Lower the presser foot and resume sewing. However you can change the thread tension as follows. Press the fuction F5 button directly under the tension mark. LCD changes to the thread tension mode. When you turn on the machine, straight stitch will be selected automatically.
Select utility stitch pattern as follows. Page Elongation D. You may elongate the pattern by pressing the function button F3 directly under the elongation icon. Regular length b. Elongated A pattern cannot be elongated if the elongation icon is not indicated. Straight stitch with auto-reverse stitch center needle position Straight stitch with auto-reverse stitch left needle position Left needle position No.
Center needle Position No. Left needle Position No. Center needle with built-in reverse stitch No. Lower the feed dogs by moving the drop feed lever to the left.
Remove the presser foot and holder. See page 3. Good for easy to ravel and knit fabrics as well as joining durable fabrics such as denims. Blind Hem Foot D 1. Fold the fabric as shown on drawing. Place two pieces of fabric right sides together and sew a long straight stitch.
Press the seam open. Zipper foot should be used for sewing center needle position straight stitch No. It is possible that needle could hit the presser foot and break when sewing other patterns. Bar-tack Buttonhole Narrow for light to medium weight fabrics Bar-tack Buttonhole Wide for large buttons Keyhole Buttonhole for heavy weight fabrics Keyhole Buttonhole with reinforced bar tack Page 35 7. Machine will sew the buttonhole in the order as shown and stop automatically after sewing.
Press the thread cutter button and raise the presser foot to remove the fabric. To sew over same buttonhole, raise presser foot to return to original position.
Bound Buttonhole Buttonhole Foot F 1. Cut a patch of fabric 2. Baste a patch so that the center line of patch will align with the center line mark of buttonhole.
https://klodossoft.pw/views/article.php
https://abrendsoft.website/images/news.gif
https://akkpallsof21.online/article
https://abrendsoft.website/images/news.gif
https://klodossoft.online/sitemap.xml
https://klodossoft.pw/index.php
https://abrendsoft.website/images/news.png
https://klodossoft.online/
https://akkpallsoft.website/sitemap.xml
https://klodossoft.pw/views/index.php
https://abrendsoft.website/images/news.gif
https://akkpallsof21.online/article
https://klodossoft.online/
https://akkpallsof21.online/index.php
Manual singer quantum stylist 9960
WebSinger Manuals. WebQuantum Stylist™: , , Sew Mate™: , Starlet™: Stylist™ II: C C Sewing and Embroidery. Futura™: SEQS, XL, XL, . WebLearn how to use your Singer Quantum Stylist sewing machine with our instructional video series! From threading to tensions we have you covered!
https://akkpallsoft.fun/views/
https://klodossoft.online/views/
https://brekisoofg.site/views/index.php
https://brekisoofg.site/views/
https://akkpallsoft.fun/
https://brekisoofg.site/views/article.php
https://abrendsoft.website/images/news.png
https://klodossoft.pw/sitemap.xml
https://akkpallsoft.website/views/index.php
https://abrendsoft.website/article
https://klodossoft.pw/sitemap.xml
https://abrendsoft.website/images/news.png
https://brekisoofg.site/views/
https://klodossoft.pw/views/
